Tuning Tools
Holeshot 3mm Ball Extension driver for carb removal
Click image to enlarge
|
This high quality driver with 3mm ball end is just the ticket to reach those hard to get to carb intake manifold screws on the FZ1 and ZZR. The length and small shaft really make it a breeze for easy carb removal. Without the right tool this is a real pain. It features a sure grip comfort handle and high toque steel 10.5" shaft.
|
|
Holeshot 3mm Ball Driver
|
| Part No. H-BD |
$16.00 ea. |
Holeshot Float gauge
Click image to enlarge
|
Adjusting your floats to the proper level is a very critical
part of setting up your new jet kit. This high quality float
gauge is what it takes to do it right. This gauge works on all
types of carbs.
|
|
Holeshot Float gauge
|
| Part No. 35-9123 |
$42.95 |
Pilot Fuel Screw Adjustment Tool
|
Holeshot now offers this nice pilot fuel screw adjustment tool for carb
fine tuning. Many times its real tight to get in there or near impossible
to reach those pesky fuel screws. This 16" long precision adjustment tool
makes it much easier and offers a nice smooth operation with its 90
degree nylon bevel gear drive assembly. The machined aluminum knob is
marked and adjustable for keeping track of 1/4th turn increments. The
slotted driver is about 3/4" long from the base so it will reach most
fuel screws on any carb without a problem.
Note: This tool will work with slotted type pilot fuel screws only.
|
|
|
|
Click images to enlarge
|
|
Pilot Fuel Screw Adjustment Tool
|
| Part No. 35-9653 |
$72.00 |
Holeshot Piston base holders
Click image to enlarge
|
These aluminum 3/16" thick computer machined piston base
holders are a must for the installation of new high compression
pistons or a big bore kit. These go under the piston skirts
supporting them between the top engine case. This eliminates
piston rock which can turn it into a real hassle to install the
cylinder and also can cause piston ring breakage. We recommend
ordering two piston base holders for assembling 4 cylinder engines.
|
|
Holeshot Piston base holders
|
| Part No. 35-9810 |
$14.95 ea. |
Holeshot Performance Cam Degreeing Kit
Click image to enlarge
|
Dale's Cam deegreeing kit makes it simple for any home tuner or pro to
dial in your motorcycle cam timing for more power and torque.
The exclusive, Holeshot designed kit includes:
- 1 inch sweep dial indicator with 3 inch extension
to reach hard to get to retainers or tappets
- Magnetic indicator stand with fine adjustment
- Holeshot Performance degree wheel
- 10mm, 12mm, & 14mm CNC billet machined positive
piston stops to fit any engine
- Dale's own twenty minute video DVD , Step By Step
Cam Degreeing, so anyone can easily learn
- Tools lay in die cut foam and are protected by a
highly impact resistant snap shut plastic carrying case
|
|
Holeshot Cam Degreeing Kit
|
| Complete Holeshot Cam Degreeing Kit |
Part No. CDK |
$276.00 ea. |
| Cam degreeing video DVD only |
Part No. CDK-DVD |
$28.95 ea. |
| Holeshot degree wheel only |
Part No. HP-1000 |
$18.95 ea. |
Holeshot Vacuum Gauges
Click image to enlarge
|
A good carb sync is the finishing touch to any tune up or after
installing a jet kit to insure a smooth idle, good throttle response
and fuel mileage. These vacuum gauges do a very good job at a very
reasonable price for the do-it-yourself home tuner.
They include: Vacuum gauges on a sturdy mounting plate, 5mm port adapters,
in-line dampers for fine adjustment and hoses.
|
|
Holeshot Vacuum Gauges
|
| Part No. 04697 |
$64.95 |
Motion Pro Auxiliary Fuel Tank
Click image to enlarge
|
This impact resistant, portable fuel tank takes
the place of the original gas tank while performing
carb synchronizing. Includes 4 ft of 1/4" fuel line
and a brass petcock.
|
|
Auxiliary Fuel Tank
|
| Part No. 35-6897 |
$46.95 ea. |
Mityvac Brake Bleeder
 |
The Mityvac Brake Bleeder Kit makes bleeding your brakes
or clutch a snap and it is a must have when installing new
brake lines.
It creates a vacuum pulling the fluid from the reservoir down
to the bleeder valve quickly without any mess or hassle. The
complete kit includes the plastic body Mityvac, a reservoir jar
with plastic transfer lid, a brake bleeding adapter package,
24 inches of tubing and instruction manual.
|
|
Mityvac Brake Bleeder
|
| Part No. 35-5904 |
$42.00 |
Oil Filter Strap Wrench
Click image to enlarge
|
The oil filter strap wrench makes removing any motorcycle spin-on
oil filter an easy job. It features a heavy duty nylon strap and
chrome plated hex head 3/8 driver so a ratchet and extension can
also be used if necassary.
|
|
Oil Filter Strap Wrench
|
| Part No. 35-7933 |
$8.50 |
All orders plus shipping - Prices subject to change without notice
![[Back]](../images/btn_back.gif)
Disclaimer
All Holeshot Performance Products are intended for closed course racing
purposes only, never to be used on any road or highway anywhere in the world.
Many of our products are illegal on pollution controlled vehicles so installing
them is at the sole discretion of the buyer. Be sure to check your local laws.
Holeshot Performance Products is not responsible for any engine damage that
may occur from improper installation of any of its products.
Holeshot Performance Products, Inc. ® is a trademark of Holeshot
Performance. Any other product names are the trademarks of their respective
holders. All rights to use this publication are exclusively owned by, and
proprietary to, Holeshot Performance Products, Inc.
No part of this publication or
web site may be reproduced or transmitted in any form or by any means,
electronic or mechanical, without first obtaining written permission from
the publisher.
Copyright (c) 1998-2008. All rights reserved.
